![audi vcds audi vcds](https://static.vecteezy.com/system/resources/previews/000/067/044/original/vector-audi-s5-wallpaper.jpg)
The next step is to enable Security Access for the Adaptation Coding. Although there are 3 additional modes that can be added please note you can only have a maximum of 6. The following is an optional step to add additional modes to ADS system. No exit the LongCoder and Save your new settings by clicking "Do it": Go to Byte 03 and select Bit 0 "Audi Drive Select.": On Byte 00 remove the deselect bit 4 Per the image below:
#AUDI VCDS HOW TO#
We are working on figuring out how to fix it and will update the page once we do. It seems to be the key to makeing the feedback better in the steering but it does cause an error.
![audi vcds audi vcds](https://i.ytimg.com/vi/ySL2Gl6ZPWo/maxresdefault.jpg)
Warning, Although this will not give you a dash error the first bit you change DRS will cause a module not coded error in the ABS module when you make that change. This will enable the steering stiffnes changes. The final step in Long coding is make coding changs in module 44. Byte 17, bit 7, change 0 to 1 - (Enables MMI Display) From Factory these will be enabled if the equipment is installed in your car.īyte 8 Bit 3 Change 0 to 1 - Enable Suspension On MMI Menu (Magnetic Suspension)īyte 8 Bit 4 Change 0 to 1 - Enable Steering (If Dynamic steering is installed equipped)īyte 8 Bit 5 Change 0 to 1 - Enable Sports Differential On MMI Menu (If equipped)īyte 8 Bit 7 Change 0 to 1 - Enable Seat Belt tensionner (If Equipped)Įnable what you need to and don't be afraid to alter your configuration.
#AUDI VCDS INSTALL#
You will never need to enable the following unless you install the equipment. This bit will also enable S mode even when in Dīyte 8 Bit 2 Change 0 to 1 - Enable Engine (Reported for better throttle response) It wont cause any issues to enable and try it.įor 6MT I would enable bit 2 only although you can enable all of them an a 6mt car without issues.īyte 8 Bit 0 Change 0 to 1 - Enable Engine/Gearbox - Reported for DSG, Read the following note. Some people claim results from 4 and others don't. My recommendation is for Automatics to enable Bits 1,2. S-Mode, but they are still reporting good results for the other changes. Most people with Automatic transmissions are skipping bit 0 because of the car always being in Don't waste your time enabling items you don't have it wont do you any good and could cause errors. Some are for cars with the actual ADS hardware such as Sports Differential. The following enables the specific items in the MMI Menu as well as activating the feature. Byte 7, bit 5, change 0 to 1 - (Tells the car Drive Select is installed) Long Coding must be done first to enable the ADS MMI menu and allows access to the adaptation coding:Ĭhoose the "Select Control Module " Option:
#AUDI VCDS PLUS#
Now, we will check if the set up was done correctly driving with a speed that is over 15 km/h or 10 miles/h.These instructions are aimed at cars with MMI 3G plus Navigation. Then, turn buck to Documented adaption channels can be selected here / Auto-Unlock / New Value and insert number 1 (“on”) or using the “Up” and “Down” (Dn) buttons and then click Test / Save / Yes / Done, Go back / Exit. Adaption-10 / Documented adaption channels can be selected here / Auto-Lock / New ValueĪt “New value” insert number 1 (“on”) or using the “Up” and “Down” (Dn) buttons and then click Test / Save / Yes
#AUDI VCDS SOFTWARE#
Open the VCDS software that you have already installed on your laptopįollow this steps: Select Controle Module / 46-Central Conv. Plug the VAGCOM (VCDS) cable into any USB port on your laptopģ.
![audi vcds audi vcds](https://images.squarespace-cdn.com/content/v1/596eaee8a5790af30d0a26d7/1597601466232-I25WQCJVA6DVKIXETZ2B/Trackready.png)
Start the engine and connect the VCDS cable at the OBD2 portĢ. But before that, you have to use a VCDS tester and a laptop with VCDS software already installed.